MODEL 26

PORTABLE BAND SAWMILLS
  THE 26B18P20 SAWMILL

Lots of standard features you pay extra for elsewhere!    The MODEL 26B18P20 sawmill uses a smooth running and dependable 20 H.P. Honda twin cylinder engine with charging circuit and electric start with a recoil start backup.  Contrast that with other companies that offer a 9 H.P.  or 13 H.P. manual start single cylinder engine, without a trailer package, for the same price!  The trailer package has a 2” ball hitch, lights, safety chains and a 4 prong flat plug for connecting to your tow vehicle, and easily adjustable jacks on each corner support the base during cuts - even on rough terrain.  Our standard base handles logs up to 18’ long and 30” in diameter,  is expandable up to 24' cut in a single piece, and additional sections may be bolted on as needed.  Three heavy duty squaring fences and two cam-action dogs assure solid performance and complete log holding at all times, and the channel section base is heavy enough for the largest logs.  There are even receivers installed on the base for such optional equipment as loading ramps or a log loading and rolling winch as shown below.  Want more horsepower?  The model 26 can take engines up to a 20 H.P. Honda without modification.

 Our Model 26 cutting head raises and lowers quickly and effortlessly, using a chain lifting mechanism powered by a sealed gear reduction box. Chain and sprockets are used for all lifting actions, so everything is commercial quality and will last for years. All alignments are accomplished through micro adjustable locking fittings that guarantee accurate and reproducible settings. The entire mill tows smoothly behind a small  car, and the average setup time is less than five minutes.  Because of the mills compact design, it can be  easily threaded  down narrow trails to your remote building site using an ATV or even a lawn tractor, but it is sturdy enough to last for decades and tow down the freeway at speed.

 The MODEL 26 is perfect for a one man sawing operation, be It light commercial or personal use. It’s ideal for building a home or cabin, making miles of potentially expensive wood fencing at minimal cost, or providing all the lumber you need for that new barn and corral. Cuts are incredibly smooth, accurate and reproducible every time.  The Model 26 mill is based on our very successful Model 30 design, and like its big brother, may be ordered with a variety of semi-custom layouts such as different engines or bed lengths to suit your needs.  This means you only pay for the mill you want, and not the one that may be in stock at the moment.  We invite your questions about modifications to suit your plans.

















     The 20 H.P. Honda twin cylinder electric start engine provides plenty of quiet, dependable power.

Using ramps and winch post to load a fifteen inch diameter log with little effort.


















​​​
SOME FEATURES OF ALL MODEL 26 MILLS:
Heavy duty improvements. No more winch and cable now has 90 deg. gearbox with roller chain and sprockets.
















​​


SUPERIOR DESIGN
 We use the same general construction techniques in the Model 26 as in our Model 30 mills, giving you a solid, long lasting and time-tested design.  All of our mills use the same blade guides, blade types and adjustment systems, so you know the Model 26 is as good a value as the Model 30 mills that have such a solid reputation throughout the industry.  Our mills are designed using the most modern Computer Aided Design and drafting technology, and most parts are cut on our computer operated plasma cutting machine.  Each and every piece is fabricated to exactly suit the intended use and far exceed the calculated loads to which the part will be subjected.  And then every design is tested and retested in the woods around our shop to make certain that it works as intended.

VERSATILITY
The MODEL 26 may be purchased with a standard base (cutting) length of 18 feet, or you can order it with  optional  cutting lengths up  to 24'.  Additional lengths are available in bolt-on configuration if you need even more length. You can have one with your favorite engine installed, or use the standard 20 H.P. Honda, and you can get it with or without trailer package, jacks  etc. as you need.  You can even order just the head and carriage if you wish to build your own base, and without an engine should you already have a power plant you would like to use.  Since we build your saw to order, you can even have custom features on your mill that you will never find on production models, and the price is usually much lower than the standard products from other manufacturers.

VALUE
The biggest and best feature of the Model 26 mills is value.  No other manufacturer gives you all the features we do at this fantastic price!  We invite and delight in comparisons with other manufacturers.  Note the standard 20 H.P. twin cylinder electric start engine, the full 18' feet of log length capacity (not just base length) and the trailer package: All standard! Then look at the low price and our solid reputation for warranty service and superior construction methods.  Compare it all, and you too will be convinced.   We are your best sawmill value.

Getting into tight spaces is easy with the Model 26





















MODEL 26 PRICE LIST

MODELPRICE

Model 26B18P20
  -Mill with Honda 20 H.P. twin cylinder, electric start engine.
  -Trailer kit.
  -Cuts 30" dia. x 18' long log.
  -Has 3 fences and 2 dogs.

$6,795.00

Model 26B12P20

  -Mill with Honda 20 H.P. twin cylinder, electric start engine.

  -Trailer kit.

  -Cuts 30" dia. x 12' long log.

  -Has 3 fences and 2 dogs.

$6,395.00


These mills can also use engines other than those shown.  Call for particulars and current pricing. 




MODEL 26 OPTIONAL EQUIPMENT

MODEL
PRICE

Fender kit

  -for all Model 26 mills equipped with trailer kit

$85.00

Loading ramps (pair)

  -8' long, used for manually loading logs onto cutting deck with cant hook or loading winch below.

$300.00

'T' stands (pair)

  -used in conjunction with loading ramps above, convert ramps to log deck.

$45.00

Loading winch

  -manual winch for rolling logs up ramps above and for turning cants and large logs on the cutting bed.

$150.00

Bed Extension

  -extra bed length added at time mill is ordered, built into mill bed and non-removable.

  -(Example: 26B12 with two additional feet would become a 26B14).

  -Sold by the foot.  Call for details.

$95.00 per foot

Base Extension

  -Adds extra bed length, bolt on extension sold by the foot, to any length.

$105.00

Trailer kit

  -for model 26 mills not originally equipped with a trailer. 

  -Includes wheels, tires, lights and a 2" ball type hitch. 

  -Some welding required if not factory installed.

$810.00




PARTIAL MILLS and parts FOR OWNER COMPLETION

MODEL
PRICE

Model 26 (head and carriage only)
  -for owner supplied base and engines.  
  -Does not have base, engine, engine drive pulley, drive belt or electrical system, but otherwise complete.

  -For electric or gasoline power plants.

$3,984.00
Model 26P20 (head and carriage)
  -Complete with 20 H.P. Honda electric start engine, electrical system, etc.  
  -All up and running except for base.
$5,560.00
Dog Assembly
  -Bolt-on or weld-on style to fit owner-built base.
$115.00 each
Fence Assembly
  -Bolt-on or weld-on style to fit owner-built base.
$55.00 each
Replacement Bandwheel tires
  -type B-47
$18.50 each
Replacement carriage wheel
  -Four required per saw
$18.50 each
Replacement Drive Belt
$23.50 each


How are we so Inexpensive?
We are located in Arkansas, where costs are low, land and buildings are inexpensive, and taxes are reasonable.  We pass these savings along to our customers.

We are not 'top' heavy.  We do our own work, answer our own phones, write the manuals and make the parts. We build and maintain our own web site and sometimes that takes us awhile! 

We like what we do and it shows in the quality of our products. 

You won't find anyone at MISTER SAWMILL that isn't interested in providing the best service for our customers. That includes selling you what you need and not what may make us the most profit.

We are working folks, just like you. Our hands and clothes get dirty, but the job gets done. We like things simple and easy to operate, and we definitely want our machines to work for extended periods of time with little maintenance and low operating costs.